hyosung cash dispenser error

1. Received a request for over 150 notes dispensing on the Cash Dispenser from the upper unit. Realign notes in the cassette3. Recover printers mechanical error 2. Reboot ATM. Check settings of 4 Cassette FM Board Dip Switch (#3, #5, #6 On) 6. ), When sensing CS4B Dark (Error code, 400FF00 is subdivided by location of sensor. Remove jammed notes on Cash Dispenser return path 2. Stack, No envelop in entry sensor (wait time 3 sec) ? 2. 4. If all programming appears correct, contact the processor and have them trace the Terminal ID. Check the front of the CDU and the cash tray for blockage. HYOSUNG CE - E.5 MODEM ERROR CODES: D030000: Modem is not responding: Check the modem controller. Check the Cutter module 2. No carrier during data sending/receivingafter the modem is connected. Check Host Connection. Check the thermal printer head and change if necessary. C001x. If they The disable address parameter contains dialing control characters that are not processed by the service provider. 1. This ATM provides two advantages including a larger touch screen (19 inches) and 5 removal cassettes. Remove jammed notes on Cash Dispenser return path 2. Rearrange notes in cassette3. Paper jam detected before executing command, Paper setting error detected before executing command, Paper check error detected before executing command, Paper cutter software check error detected before executing command, Open lever detected while executing command, Receipt printer head overheated while printing, Paper jam detected while executing command, Paper cutter software check error detected while executing command, No response detected for 30 seconds after sending command. Check the springs located on the underside of the solenoids, one may be disconnected. Check CS3 Sensor BKRT3. Try Balance Inquiry. 3. Check the transaction from the host and try again. Exchange a sensor after abnormal operating the CS37 sensor . 6. 1. Remove the dust on the CS41A and CS41B sensors. Something is detected on CS14 sensor after dispense operation. Hyosung: 4005700: Cash dispenser configuration error: Hyosung: 4005800: Retract box position error during . Remove note from the CDU delivery path. Clean CS1B and CS13, CS11B and CS13 Dark detection during initializing or dispense reserved operation, The same as #40022 and #40028 error handling, CS1A, CS1B or CS13 sensor detects note in delivery path before/after CDU dispenses, 1. of dispensed notes that software counts 1. Check if CS62 sensor poll is abnormal3. 2. Check that Dual Master Key is disabled (non Coredata). Check all wiring connections to CDU mainboard. Check wiring to mainboard. Reconfigure currency, In case requested bill counts are exceeded the maximum count, In case the number of bills dispensedexceeds the maximum dispensing bill, 1. Remove a jammed note at the position of the CS13 sensor 3. 1. 1. CS2 and CS3 Dark detection during initializing or dispense reserved operation, The same as #40011 and #40012 error handling, CS4A sensor detects note in delivery path before/after CDU dispenses, 1. Rearrange notes in Cassette 3. Remove the remaining notes and foreign objects at the position of the CS31AB sensor 2. CS31AB ~ CS13 Time out (Jam) during dispensing bills from fourth cassette. FS omitted (after total cash dispense amountFS omittedin day (after total non cash dispense Verify that version of Mini-Bank Software matches host processor. Initialize after Reset Power2. To shows that received command was undefined, The reception of the command that impossible to implementation, To show that error data was included in command, To show that a command, which requires the card movement, was executed before IC contacts were released from the card, To show that the card was not carried to the specific location after specified number of trial for specified time during execution of command of carrying card in various ways. If persistent, clean and test the card reader in diagnostics. You may also want to try the reset button on the printer to clear this error. Time out(30sec.) Hyosung Monimax 5800 / 5800T:mono function ATM. Initialize3. 2. Disable to drive due to continuous CS14~CS10AB Dark during forced initialization or retract operation (jam), Disable to drive due to continuous CS10 Dark during forced initialization or retract operation (jam), Failed to fall down bills during forced initializing and retract operation. Command, Gate operation sensor (CS3) error before initial recovery, 1. Remove foreign objects on 4 Cassette Clutch Encoder Slit.4. Check external light source of the CS 15 sensor. Check the notes in cassette #3, In case partial bills only are dispensed from the requested bills. Bill rejection error (Normal recognition for short bill-CS4), Bill pickup sensor(CS1, CS15) recognized has a hole and CS4 sensor detects it or CS4 snesor detects the gap too close. Check foreign objects in the main motor encoder slit5. Check the cassette catcher2. 4. Cash cassette 1 removed prior to dispenser. Error of being removed 2nd cassette before separate rejection, 1. In line filter may help this. 2. Clear the cash tray of any bills or foreign objects. Remove the remaining notes at a sensor in front of the CST 2. Failed to connect communication between Receipt printer and SP. 1. Remove the remaining notes and foreign objects in the throat unit. 1. Check dust in Main Motor Encoder Slit 4. Inquire about credit card account to bank. Remove the remaining notes and foreign objects at the position of the CS4 sensor 2. Check bill jam or no note in cassette #22. Set serial number. Remove a dust or foreign objects on the CS13 sensor4. 1. Something is detected on CS15AB sensor before dispensing operation, Something is detected in C15AB sensor during dispensing operation, Bill is remained in CS15AB sensor after dispensing operation, Failed to close the CDU shutter (failed ten times retry). Reenter the password correctly. If no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust). Try download again. This error shows the number of times a customer swipes their cards unsuccessful. Exchange a sensor after abnormal operating the CS41A sensor. Get the trace file and log files in D:\trace 2. Check settings of 3 Cassette FM Board Dip Switch (#2, #4, #6 On) 3. Check CS15A Sensor Cable3. 4 Cassette Jam during dispense operation (4 CST Encoder Error). (26 pages) Cash Counter Nautilus Hyosung MONiMAX7800T Installation Manual. Clean CS4A, CS2 or CS4A sensor detects note in delivery path before/after CDU dispenses, 1. Check if Dip switch #6 is correctly set (Dip switch #6 is set by On in case of not using Black mark). 1. Check if the CS41A sensor cable is disconnected (4 CST FM B/D CN3).6. Try cleaning the cassette and dispenser. Check modem and modem cable connection 2. CDU double detect module failure 1 (while re-dispensing). Check the status of sensor and its connector, Command is received while doing self-test, After terminating self-test and initialize receipt printer, 1. Replace cash dispenser PCB2. Check the reject analysis to determine the cause of reject (reports menu). Remove the remaining notes or foreign objects in the tray. Replace cash dispenser PCB 2. Check CS8 Sensor Cable 6. Replace the Cash Dispenser B/D: 40055 (DISPENSE) Detect CS13 during constant speed of motor / CS13 Jam during dispensing. If error occurs after checking CS 15 disconnection and operation, replace a sensor. Install after rearranging notes in cassette, 1. Check if the CS11AB sensor cable is disconnected 3. 1. To show that read error has happened in Multiple magnetic read command. Clean CS2 and CS4B. Check dust in Main Motor Encoder Slit 4. ICRW tried to activate with ICC/SAM, but the card returned ATR, which is not supported. Check cassette sensor. Error Codes Home ATM Service Error Codes Are you interested in upgrading or replacing your existing ATM machine? Verify that version of Mini-Bank Software matches host processor. Reinstall software 3. Check the CDU firmware version and refer to not have from the upper unit specifications. CDU ROM does not match AP software. Exchange Sensor after abnormal operating CS7 Sensor, CS21B DARK Detected (Initial recovery, Separated reject), 1. The ATM time, as set in the Operator Function Menu, is incorrect. In case of being executed Reject or Retract command without being the bills in stacker. 2. Rearrange notes in cassette 3. Remove the remaining notes and foreign objects at the position of the CS 15 sensor 2. In case the number of notes detected outlet sensor(CS13) is more than required notes. 1. 1.?Check RMS-related settings. Clean CS1A and CS1B, CS13 sensor detects note in delivery path before/after CDU dispenses, 1. Remove the remaining notes and foreign objects at the position of the CS41A and CS41B sensors. NOTE: This error occurs only if there is no dial tone at the mainboard. Remove dust in CS13 Sensor 4. Exchange Sensor after abnormal operating CS3 Gate detecting Sensor. If consistent, it can be a defective modem. Check and reseat all belts. This can also be a problem with programming, check all programming (especially Dual Master Key setting and Host Processor Mode). Check the condition of the cash in the cassette. Exchange a sensor after abnormal operating the CS21AB sensor, CS31AB Dark detection on transport path before dispense operation, 1. Check the transaction from the host and try again. Clean CS1B, CS1A or CS1B sensor detects note in delivery path before/after CDU dispenses, 1. Remove dust in CS1~CS4 sensor 3. 3. Initialize. Hyosung TNS . Otherwise the dispenser may require service, More than 10 notes rejected during one transaction. Check Index of notes 4. Check if the CS3 sensor cable is disconnected(CN10 #9~10) 5. Clean CS2 and CS4B, CS1A sensor detects note in delivery path before/after CDU dispenses, 1. Check if the CS5 cable is disconnected (CS5_1:Cash Dispenser B/D CN10 #11~12, 25~28/ CS5_2:CN12), _ Check notes status in the reject box _ Realign notes in the cassette _ Check foreign objects at the position of the CS5 Sensor Guide _ Check if the CS5 cable is disconnected (CS5_1:CDU B/D CN10 #11~12, 25~28//CS5_2:CN12). Depending on the model of dispenser there are different causes and possible solutions. Exchange 1 cassette box when there are many error, Error if the number of dispensed notes is not matched to the requested, 1. Paper of a lesser thickness is more prone to jamming. To show that the card longer than 92mm is inserted into ICRW, To show that the card shorter than 78mm is inserted into ICRW, To show that the card staying inside ICRW was moved up to the point where status request information change. The error of separation time from CS15 to CS4, Something is detected on CS31A, CS31B sensor during initialization, Something is detected on CS31A, CS31B sensor in initialization. Check notes dispensed and rejected 2. Remove note from the CDU delivery path 2. 5. (Currency, Denomination, etc). 5. 1. Check if the RMS host is alive. In case other command is executed in Cash Unit Exchange, Cash dispenser service is already cash in state, In case the cassette counting dont match, In case the number of cassette dont match. Reconfigure denomination 2. Check jam in 1 cassette and reload4. Check the replenished amount and replenish2. The target call address has call blocking enabled. 1. Check command that Cash Dispenser is received 2. Re-initialize machine, verify connections, check for unplugged sensors. Check state of notes in reject box 2. Error of being removed 2nd cassette before separate rejection, 1. 3. Check index value of notes each cassette, In case the number of notes detected outlet sensor(CS13) is less than the number of required notes, 1. Check a dust in stacker 2. PROCESSING ERROR (STANDARD3), Refer to E7. 2. Check the transaction from the host and try again. The HALO II uses proven cash dispensing technology engineered for maximum up-time widely regarded as the best in the industry. Set information of Cash Dispenser Unit if error is not cleared after power Off/On. Detected notes in path before initializing. 2. It provides end-to-end solutions best fit to each cash point - teller line, back office and self-service channels. 1. (See definition of C0011 error) this is typically a bounce back of a bill during dispense causing the exit sensor to remain blocked for a longer time than is expected. Check if 3 Cassette FM B/D CN2 and 4 Cassette FM B/D CN1 are connected. Check Cash Dispenser Unit information. Check the cable and connection between the CE and printer. Usually caused by a customer putting fingers in the cash drawer during dispense. Remove a jammed note in 3 Cassette.2. Exchange sensor after abnormal operating CS21A, CS21B Sensor, 1. 2. Check the abnormal communication cable. 1. Remove note from the CDU delivery path. Check 1 Cassette specification3. Exchange Sensor after abnormal operating, 1. 3 Cassette not available during dispense reserved operation. Replace Reject Solenoid 1, 1. Simultaneous Dark detection in both the tray (CS10) and throat (CS14/CS15). ), Cash picking-up fail while cash in cassette #1 is enough, 1. Remove jammed notes on Cash Dispenser return path2. Check all wiring to mainboard. Check the cassette catcher 2. Remove the remaining notes and foreign objects at the position of the CS11AB sensor 2. 1. Remove note from the CDU delivery path. Remove a jammed note between the tray and Cash Dispenser. Opened shutter during dispense operation. Remove a jammed note between the tray and Cash Dispenser 2. Remove a jammed note between the tray and Cash Dispenser2. Remove jammed notes on Cash Dispenser return path 2. Check cash dispenser driver (CDM SP) version2. Mount 4 cassette1. Check for any CDU error codes and the number of. 4.?Check the modem controller and logic. Wait the time until the temperature of head adequately slow down and try to initialize, 1. Check the catcher inside cassette #2 guide, Field Error (This Field must have initial value). Check vault door switch. Received the wrong life test command from the upper unit. 1. 2. The ATM attempted to do a reversal and could not. Detecting CS2 Dark (Front Access Type:Reject box is opened. 2. 1. Reconfigure cash dispenser setup data: 4005800: Retract box position error during command reserved operation: 1. Check CS1 sensor 2. Use a business card or stiff paper to clear jams. Verify host phone number See D170x. When "Low Cash Warning" is enabled in the Transaction Setup menu, this sensor will open when the cassette reaches (+/) 75 bills. If error occurs when checking disconnection operation, replace a sensor. Replenish receipt paper in paper charger 2. Check the replenished amount and replenish2. No response from Host Dialing time out to Host. Something is detected on CS15AB sensor before dispensing operation, Something is detected in C15AB sensor during dispensing operation, Bill is remained in CS15AB sensor after dispensing operation, 1. Check if the CDU Board CN6 and 3 Cassette FM Board CN1 are connected. Check CS8 Sensor Cable 6. To show that only SS,ES,LRC are contained in the track. C0030. 2. This white plunger switch is located in the upper left corner of the vault, or on along the front edge of the cash dispenser tray. Verify that version of Mini-Bank Software matches host processor. Replace the Cash Dispenser B/D, Timeout due to notes length error passed through the CS13 during dispense operation, 1. Initialize after Reset Power 2. Response Type missmatch (Withdrawal/Balance/Transfer). Remove notes or dust in existence CS21A Sensor 2. Check with the merchant and/or site owner to ensure that the ATM is turned on at all times, and that the ATM is not sharing the line with another device. It was detected that the feed lever was open while the receipt printer was operating. Change Cash Dispenser B/D, Error of two sheets detecting sensor(CS5_1)for initializing, 1. If error occurs when checking CS11B cable operation, replace a sensor. Check the dispenser information using the CDU Test Program. Initialize 3. If no bills are present try using compressed air to clean the dispenser (a sensor may be blocked by dust). CDU sensor is tripped. Initialize after removing notes or dust over Gate. 1. Initialize 2. Dark Light Test Error (CS10, CS9) during initializing. Clean CS1A and CS13, 1. - PIN ERROR?1. Remove note from the CDU delivery path. Check Main Motor Encoder Slit 3. Check if the CS41A and CS41B sensor cables are disconnected (4 CST FM B/D CN3).Exchange a sensor after abnormal operating the CS41A and CS41B sensor. Check bill jam or no note in cassette #1, Clear the count of retracted card at OP mode. 1. Otherwise the CDU will require repair / replacement. Check logic related to the sensor in the Cash Dispenser Unit board. Remove note from the CDU delivery path.2. 2.2K views 2 years ago. 20003. Replace 1 cassette box when multiple errors occur. Insert or re-insert the cassette(s). Check settings of 3 Cassette FM Board Dip Switch (#2, #4, #6 On) 5. Remove jammed paper Release receipt paper drawer by pressing the tab with the green sticker located at the front of the printer. Check foreign objects at the position of the CS5 Sensor Guide 4. Check and verify all connections to the dispenser circuit board. Realign notes in the cassette 3. Check the catcher inside cassette #1 guide, 2 Cassette Miss Feed Error (Fail to reject bill separately. Replenish receipt paper in paper charger 2. Remove dust in CS11AB, CS21AB, CS31AB, CS41AB, CS4AB, CS13 Sensor 3. CS 14 Dark detection during initializing or dispense reserved operation. Check the status of Near End sensor and its connector, 1. If the same problem occurs, inject master key again by diagnostics or inquire your service provider. ), Dark light sensor error (CS21A, CS21B) during idle status of cash dispenser, Cash picking-up fail while cash in cassette #2 is enough, 1. Download, Erase Error(Flash Memory Erase) ?Download, Flash Memory Sector size error ? Replenish receipt paper 2. Cash Dispenser Unit data(country, cassette, shutter)setting error occurs during initialization. Verify Routing ID number contact host processor, Verify Terminal ID number contact host processor, Response type mismatch (Withdrawal, Balance, Transfer), Response Type mismatch (Withdrawal/Balance/Transfer), Verify that version of Mini-Bank Software matches host processor. 2. Cash Dispenser(CDU) received the undefined command from AP software, 1. Complete the contact form below and well follow up right away. Reset the demand to less than 4 in the CE. If error occurs when checking CS11A cable operation, replace a sensor. CSB sensor detects note in delivery path before CDU dispensesSensor is located along the delivery path right after where the note exits the 1st cassette. Clean CS4A and CS4B. Initialize3. Rearrange notes in cassette 3. Check 2 cassette specifications 3. Disconnected by rejected call from remote party Try again later. Similar to the COO11 error, this would indicate a bill jam close to the exit of the CDU or near the reject bin. Check the CS9 sensor (double detect sensor). Low Cash. Replace 1 cassette box when multiple errors occur. Change CS5_2 Sensor, Error of CS 2, CS13 sensor during initialization, Error of 2 sheets detecting sensor(CS5_1/CS5_2), 1. Loose belts can slip off rollers and block sensors. Check abrasion of the cassette box pick unit. Check coin dispenser driver version2.Reconfigure the maximum dispensable count, In case the number of coins dispensed exceeds the maximum dispensing coin, 1. 1. Check cash dispenser, Not setting deposit direction, and Inquire Accept() method, Not setting deposit denomination, and Inquire Accept() method, Set incorrect denomination when executing Enable()/Disable(), Set correct denomination after confirming currency, Set incorrect direction when executing Direction() method, Call Direction()/Enable()/Disable() method under no initialization, Clear the count of retracted card at OP mode, Command execution is impossible under Supervisor program code area. Contact to host and phone company. Check notes in Reject Box 2. 1. Check CS8 Sensor Cable. In case the dispensed denominations are different from the requested ones. Check communication cable 3. Remove notes on CS2 sensor 2. If error occurs when checking TS004 disconnection and operation, replace a sensor. Check cable and connection between the CE and printer. HYOSUNG CE - E.4 CASH DISPENSER ERROR CODES: 1102910: LOST WITHDRAW CASH", DEV_CSH: 1102920: LOST DEPOSIT CASH", DEV_CSH: 1103910: LOST CARD & SLIP", DEV_MCU | DEV_SPR: 2000100: No cassette: Insert or re-insert the cassette(s). Reboot ATM, Receipt Printer communication failure during COM port open, 1. Check BIN List. If they are broken the cassette will not stay in the dispenser. Test Modem. 2. Check the dispenser gate solenoid cable and connection. Do not use spaces or dashes in the phone number string. Replace cash dispenser PCB2. 4. Reset the cassette, check position of microswitch on right rear wall of cassette bay in the dispenser. Do RESET at Operator Function 2. Check settings of 4 Cassette FM Board Dip Switch (#3, #5, #6 On) 5. Check the remaining notes in 2 Cassette2. Call to find out how easy it is to swap out machines. Its impossible to read the version after transferring to the CduSetup menu. If the cash is of known good quality then try cleaning the cassette and dispenser. Reconfigure denomination2. Replace Reject Solenoid 1. 4. Corrective steps: 1. CS31AB~CS13 Time out(Jam) during dispensing from 3rd cassette. The remaining notes on the tray during delivery operation (some notes remaining on CS10AB), The remaining notes on the tray during delivery operation (some notes remaining on CS14), 1. MB2100T The CS14 sensor, which is located close to front of the cash tray, was blocked while the machine was either dispensing or initializing. The specified country/region code is invalid. 2. Check CS7 Sensor Cable 3. 2. CS11AB Dark detection on transport path before dispense operation, 1. Exchange a sensor after abnormal operating the CS4 sensor, 1. Reject bin is not in the correct position. The NVRAM has been cleared, and the master password must be reset to default before the ATM can be reprogrammed. 1. Continuously detected note in CS15 during retract operation. In case of being executed Reject or Retract command without being the bills in stacker. Check the status of sensor and its connector, 1. 1. Remove the remaining notes and foreign objects at the position of the CS31B sensor.2. Check modem and modem cable connection 2. Sensor is located along the delivery path right after where the note exits the 1st cassette. Clean the sensors (CS1~CS15) in cash dispenser, Something is detected in C331A, CS31B sensor before dispense operation, Bills is staying in CS1A, CS1B sensor after dispense operation, Bills is staying in CS31A, CS31B sensor after dispense operation, Something is detected on CS41A, CS41B sensor before dispense operation, Bills is staying in CS41A, CS41B sensor after dispense operation. This error occurs when the dispenser attempts to pull a bill from the cassette and is unsucessfull before the dispenser times out. Reboot ATM. Clean CS2, CS4A and CS4B, CS2, CS4A and CS4B Dark detection during initializing or dispense reserved operation, The same as #40011, #40014 and #40018 error handling, CS3, CS4A and CS4B Dark detection during initializing or dispense reserved operation, The same as #40012, #40014 and #40018 error handling, CS2, CS3, CS4A and CS4B Dark detection during initializing or dispense reserved operation, CS1B or CS13 sensor detects note in delivery path before/after CDU dispenses, 1. Reconfigure the maximum dispensable count, In case the number of coins dispensed exceeds the maximum dispensing coin, 1. Clean CS2, CS4A and CS4B. means cassette number. Check the printer head and change if necessary. 1.Check RMS-related settings. Check the abnormal communication cable. Check notes status in 4 Cassette 2. ), Cash picking-up fail while cash in cassette #4 is enough, Dark light sensor error (CS31A, CS31B) during idle status of cash dispenser, Cash picking-up fail while cash in cassette #3 is enough, Dark light sensor error (CS1) during idle status of cash dispenser, Dark light sensor error (CS41A, CS41B) during idle status of cash dispenser, When sensing bills in the Stacker (Error code, 400FF00 is subdivided by location of sensor. Remove notes on CS2 sensor 2. 1. 2. Realign check sheets in the check cassette box.5. Check modem cable 2. Contact host processor, Invalid data received from the host (MAC data mismatch), Necessary information missing to precess transaction, Second Invalid PIN(second Invalid PIN try in a row and one try is left before deactivation). 1. Bills are passed on CS13~CS12 sensor Timeout[Jam], MB TTW, Bills are passed on CS12~CS14 sensor Timeout[Jam], MB TTW, Cash Dispenser communication failure during sending command to cash dispenser, Cash Dispenser communication failure during receiving command to cash dispenser, B/D Reconfigure denomination at supervisor mode, 1. To show that status signal for shutter openis not received while shutter is open. Press Enter -> Clear -> Cancel -> 1 -> 2 -> 3. Check dust existing in CS5 Sensor Guide 5. 2. Check sensor for debris. Check the shutter cams rotation operation. ), 1. Upgrade the Cash Dispenser firmware or download software again3. Check the Cash Dispenser received command 2. Remove a jammed note in 1 Cassette.2. Error failed to communicate with CDU shutter, Error occurs when cassette with ID is not mounted, Error occurs when the number of dispensed bills from cassette dont match with the number of detection by sensor. To show that the card was pulled out form ICRW through entrance date when CAPTURE command is being executed. Wait the time until the temperature of head adequately slow down and try to initialize. Remove note from the CDU delivery path. Check dust existing in Main Motor Encoder Slit6. 1. Upgrade the Cash Dispenser firmware or download software again 3. Appendix Error . Check notes dispensed and rejected 2. Remove any notes from path. 4. Rearrange notes in cassette 3. 1. Exchange Cash Dispenser B/D, 1. Reject gate failure while initializing or dispensing note. Change Main Motor Encoder Slit Sensor CS8. Use an electrical parts contact cleaner on terminals. Check if 3 Cassette FM B/D CN2 and 4 Cassette FM B/D CN1 are connected. The specified terminal identifier is invalid. Try different cards. Check notes status in the reject box. 9719600 The abnormal of the number of Cash Unit Reconfigure cash dispenser setup data. Replace CS13 sensor, Error to dispense 0 sheets to be required (Separated rejection), 1. Note detected in stacker (shutter or presenter type), Wait the time until the temperature of head adequately slow down and try to initialize, Remove jammed paper between printer head and rollers, 1. 5. Check dust in existence CS5 Sensor Guide 5. inside left wall of the dispenser. 1. Remove note from the CDU delivery path. Check the total paid money from ATM. Page 39 MoniMax 5600T 4. Initialize after removing notes or dust2. Remove note from the CDU delivery path.2. Reboot ATM. Check cables between CDU and Mainboard, remove cables (even though they may be attached) and re-connect. Replenish receipt paper2. Check modem cable 2. Otherwise the printer needs service. Realign notes in the cassette 3. Remove a jammed note on the CDU.3. Verify cash count in the Settlement menu. Check notes in Reject Box 2. Check if the CS5 cable is disconnected, 1. Replenish receipt paper in paper charger. Reconfigure denomination at supervisor mode. 1.Remove a jammed note in 4 Cassette. Inquire about the problem. ), When sensing CS4A Dark (Error code, 400FF00 is subdivided by location of sensor. Check the abnormal communication cable. Change Main Motor Encoder Slit Sensor CS8, Failed in checking the reject gate solenoid echo, Failed in checking the present gate solenoid echo, 1. Dark light sensor test error (CS41A, CS41B) during initializing. Check the replenished amount and replenish 2. Reboot ATM, Memory Allocate Error (PrintForm Allocate IndexBuffer Fail), Field Error (This Field must have initial value), Cash Dispenser communication failure during COM port open, 1. Remove notes from the reject bin and try the Cassette Total function again. If this machine is typically stocked with a low amount of bills, we recommend disabling this function. 4. CS4 sensor detects note in delivery path before CDU dispenses Sensor is located along the delivery path right before the reject bin. Check for any CDU error codes and the number of notes dispensed to customer. Check the wiring connections to the solenoid(s). Exchange CS8 Encoder Slit Sensor. 2. Remove jammed paper- Release receipt paper drawer by pressing the tab with the green sticker located at the front of the printer. Check the CDU firmware version and refer to specifications. 1. Replace 2 cassette box when multiple errors occur. 2. 1. Check phone number. 1. 4. Remove notes or dust on CS15A Sensor 2. Check abnormal clutch. Check notes in Reject Box 2. 2. 1. Remove note from the CDU delivery path. 800-951-9533. This is not an error in particular, but a simple warning that someone was locally on-site at the ATM, and used its Operator Function menu. 1. Receipt printer head overheated before printing. Check Index of notes 4. In case partial bills dispensed by dispensing demand when Partial Dispense option is on._ X means cassette number. 3. Realign notes in the cassette 3. 1. Check the transaction from the host and try again. 1. Check notes in Reject Box 2. Check the notes in cassette #2, 1. Also, if the wrong parameters are entered when the CDU is programmed, this error can occur. Otherwise the printer may require service.

Atlantic City Sportsbooks, Spring Of Power Dragon Not Showing Up, Counsel Of Ahithophel Kjv, Rob Nelson Fixer To Fabulous, Is Kent School District Open Today,